SAM #N0010426QNE78

NAVSUP WSS Mechanicsburg Solicitation for Disk for 5-inch Hull and Backup Valve Assembly

NAVSUP Weapon Systems Support Mechanicsburg, part of the Department of the Navy, is seeking a disk for a 5-inch Hull and Backup Valve Assembly. - Government Buyer: - NAVSUP Weapon Systems Support Mechanicsburg (Department of the Navy) - OEMs and Standards Referenced: - Naval Sea Systems Command (OEM for drawings/specifications) - EB Specification 2937 - ASTM-B564 (UNS N06625) - Multiple quality standards: ISO-9001, ISO10012, ISO/IEC 17025, MIL-STD-792, MIL-I-45208, MIL-STD-45662, ANSI/NCSL Z540.3, FED-STD-H28 - Products Requested: - Disk for 5-inch Hull and Backup Valve Assembly - Manufactured per Naval Sea Systems Command Drawing 845-7016098 Item 13 and General Notes Drawing 803-5959311 - Material must comply with EB Spec 2937 or ASTM-B564, UNS N06625 - Supplementary Note S2.A applies - Unique/Notable Requirements: - Certifications required: weld repair, ultrasonic inspection, dye penetrant inspection, alloy identity test - Forging sketches and first article testing - Strict traceability and quality assurance procedures - Special emphasis material designation - Configuration control and certificate of compliance - Mercury-free materials - Government source inspection - Critical safety item for shipboard systems

Description

CONTACT INFORMATION 4 N744.24 WVN 771-229-0476 HEATHER.R.JONES52.CIV@US.NAVY.MIL ITEM UNIQUE IDENTIFICATION AND VALUATION (JAN 2023) 19 <!-- Additional items omitted for brevity --> HIGHER-LEVEL CONTRACT QUALITY REQUIREMENT (DEC 2014) 1 SEE SPECIFICATIONS SECTION C AND SECTION E. INSPECTION OF SUPPLIES--FIXED-PRICE (AUG 1996) 2 INSPECTION/ACCEPTANCE POINT 6 TBD TBD TBD TBD TBD TBD GENERAL INFORMATION-FOB-DESTINATION 1 A WIDE AREA WORKFLOW PAYMENT INSTRUCTIONS (JAN 2023) 16 STAND-ALONE RECEIVING REPORT - CERTIFICATIONS; COMBO - RECEIVING REPORT & INVOICE - MATERIAL. N/A TBD N00104 TBD TBD SEE SCHEDULE TBD SEE FORM DD1423 NAVY USE OF ABILITYONE SUPPORT CONTRACTOR - RELEASE OF OFFEROR INFORMATION (3-18) 1 WSS MANDATORY USE OF WORKFLOW PRO (WFP) MOD ASSIST MODULE 1 WARRANTY OF SUPPLIES OF A NONCOMPLEX NATURE (JUNE 2003) 6 ONE YEAR FROM DATE OF DELIVERY ONE YEAR FROM DATE OF DELIVERY ... <!-- Additional sections omitted for brevity --> 1. SCOPE 1.1 The material covered in this contract/purchase order will be used in a crucial shipboard system. The use of incorrect or defective material would create a high probability of failure resulting in serious personnel injury, loss of life, loss of vital shipboard systems, or loss of the ship itself. Therefore, the material has been designated as SPECIAL EMPHASIS material (Level I, Scope of Certification, or Quality Assured) and special control procedures are invoked to ensure receipt of correct material. 2. APPLICABLE DOCUMENTS 2.1 Order of Precedence - In the event of a conflict between the text of this contract/purchase order and the references and/or drawings cited herein, the text of this contract/purchase order must take precedence. Nothing in this contract/purchase order, however, must supersede applicable laws and regulations unless a specific exemption has been obtained. 2.2 Applicable Documents - The document(s) listed below form a part of this contract/purchase order including modifications or exclusions. 2.2.1 Documents, drawings, and publications supplied are listed under "Drawing Number". These items should be retained until an award is made. 2.2.2 "Document References" listed below must be obtained by the Contractor. Ordering information is included as an attachment to this contract/purchase order. 2.2.3 Specification Revisions - The specification revisions listed under "Documents References" below are the preferred revision. Older and/or newer revisions are acceptable when listed within Contract Support Library Reference Number CSD155 in ECDS (Electric Contractor Data Submission) at: https://register.nslc.navy.mil/. This is to allow Contractors to use certain acceptable older specification revisions to purge their existing stock of material certified to those older revisions or to use newer specification revisions when material is certified to newly released revisions, without requiring the submittal of waiver/deviation requests for each specification revision on every contract. Revisions of specifications reflecting editorial and/or re-approval (e.g., E2009, R2014, etc.) are considered inconsequential, but are acceptable when their revisions are listed within CSD155 or elsewhere within this contract. <!-- Additional content omitted for brevity -->

View original listing