SAM #N0038326QMB03

Repair and Modification of Drawer, Power Distribution, A for NAVSUP Weapon Systems Support

NAVSUP Weapon Systems Support, Philadelphia (Department of Defense, Department of the Navy) is seeking repair and modification services for a critical aircraft component. - Government Buyer: - NAVSUP Weapon Systems Support, Philadelphia - Department of Defense, Department of the Navy - OEM Highlight: - Northrop Grumman Systems Corporation is referenced as the item source - Products/Services Requested: - Repair, modification, testing, and inspection of Drawer, Power Distribution, A - Part Number: 123av50587-301 - NSN: 1680 015628732 - Item must be restored to Ready for Issue (RFI) condition - Key Requirements: - All work performed at contractor's facility - Contractor supplies all necessary parts and materials unless otherwise specified - Quality control system must comply with ISO 9001/SAE AS9100 - Calibration system must meet ANSI/NCSL Z540.3 or ISO-10012-1 - Configuration management required - Strict adherence to approved repair manuals, drawings, and specifications - Use of MIL-W-81381 wire is prohibited; SAE-AS22759 series wire required - Compliance with MIL-STD-130 for markings - No government-furnished equipment or tooling provided

Description

CONTACT INFORMATION 4 N761.37 P1G 215-697-2983 ETHAN.STEIN@NAVY.MIL ITEM UNIQUE IDENTIFICATION AND VALUATION (JAN 2023) 19 HIGHER-LEVEL CONTRACT QUALITY REQUIREMENT 8 X INSPECTION AND ACCEPTANCE OF SUPPLIES 26 X WIDE AREA WORKFLOW PAYMENT INSTRUCTIONS (JAN 2023) 16 | INVOICE AND RECEIVING REPORT COMBO TYPE | SOURCE/SOURCE | TBD | N00383 | TBD | TBD | SEE SCHEDULE | TBD Additional details omitted for brevity... All contractual documents (i.e., contracts, purchase orders, task orders, delivery orders, and modifications) related to the instant procurement are considered to be "issued" by the government when copies are either deposited in the mail, transmitted by facsimile, or sent by other electronic commerce methods, such as email. The government's acceptance of the contractor's proposal constitutes bilateral agreement to "issue" contractual documents as detailed herein. Early and incremental deliveries are accepted and preferred. 1. Scope 1.1 Markings shall be in accordance with MIL-STD-130. 1.2 Articles to be furnished hereunder shall be repaired, tested, and inspected in accordance with the terms and conditions specified in the Requirements Section of this document. 1.2.1 Any item contracted for repair SHALL have a Statement of Work to ensure compliance with all repair procedures and requirements. Repair of: DRAWER, POWER DIST, A Part Number: 1680 015628732 NSN: 123av50587-301 Available repair manuals, drawings, and specifications per p/n requirements 1.2.2 There will be no repair deviation from the approved written procedures without review and acceptance by the Basic Design Engineer. All requests for Waiver/Deviation shall be via Form 1694 routed through the Local DCMA/ACO office for review and recommendations via form 1998. 1.3 Articles to be furnished hereunder shall be repaired, tested, and inspected in accordance with the terms and conditions specified in the Requirements Section of this document. 1.4 Unless expressly provided for elsewhere in this clause, equipment such as fixtures, jigs, dies, patterns, mylars, special tooling, test equipment, or any other manufacturing aid required for the manufacture and/or testing of the subject item(s) will not be provided by the Government or any other source and is the sole responsibility of the contractor. The foregoing applies notwithstanding any reference to such equipment or the furnishing thereof that may be contained in any drawing or referenced specification. 1.5 The use of MIL-W-81381 wire in any item to be delivered under this procurement is prohibited. The prohibition applies notwithstanding any reference to MIL-W-81381 wire that may be made in any of the drawings or specifications for this procurement. SAE-AS22759 series wire shall be used in lieu of MIL-W-81381 wire, in any place where MIL-W-81381 wire is cited in this procurement. Any questions concerning this requirement should be directed to the Procuring Contracting Officer. 1.6 If MIL-STD-454 is referenced in the drawings or in the specification, the contractor is expected to show compliance with IPC/EIAJ-STD-001C. Personnel performing tasks in accordance with IPC/EIAJ-STD-001C shall be trained and certified as required by IPC/EIAJ-STD-001C paragraph 5.1.4. Additional sections omitted for brevity... Additional Links: See Solicitation N0038326QMB03

View original listing