SAM #1232SA26SS1169453

USDA ARS Seeks Domestic Digital Flatbed Cutter with Tangential Creasing

The USDA Agricultural Research Service (ARS) is seeking information from potential suppliers for a domestically sourced digital flatbed cutter with tangential creasing for its NADC Visual Services in Ames, Iowa. - Government Buyer: - USDA Agricultural Research Service (ARS), Acquisition and Property Division (APD), NADC Visual Services - OEMs and Vendors: - No specific OEMs or vendors are named; the government is seeking responses from qualified domestic manufacturers or suppliers - Products/Services Requested: - Digital flatbed cutter with tangential creasing capability - Key features required: - Simultaneous creasing and cutting - 2.5 kg creasing force - High-capacity auto feeder (2,000 sheets) - 1,200 mm/sec cutting speed - Portrait or landscape sheet feed - Rear mark scanning system - Contour cutting without steel dies - Two-zone vacuum bed - Adobe Illustrator plugins - One-year warranty for parts and labor - One-year software support - No part numbers or purchase quantities specified - Unique or Notable Requirements: - Equipment must be domestically sourced (manufactured in the United States) - Emphasis on specific technical features and support - Market research only; not a solicitation for bids or proposals at this stage

Description

Sources are being sought to determine if there are manufacturers/contractors available offering a domestically sourced item that meets the minimum description outlined below. This is not a solicitation Announcement or Request for Proposal. It does not constitute any commitment by the Government. No award will result from this notice. The purpose is to conduct market research to gain knowledge of potentially qualified domestic sources. Responses to this Sources Sought Notice will be used by the Government to make an appropriate acquisition decision. The USDA Agricultural Research Service (ARS) will not award a contract on the basis of responses or pay for the preparation of any information submitted. Respondents will not be notified of the results of this notice. After completing an analysis of the responses, the Government will determine whether to proceed with issuing an unrestricted solicitation, inviting full and open competition.

Purpose:

ARS Acquisition and Property Division (APD), Acquisition seeks to determine the availability and capability of potential businesses offering a domestically available source of supply for the project below. The information received resulting from this market research will be considered for the purpose of determining domestically available sources.

Product Information:

The Government seeks information from qualified and experienced contractors capable of providing a domestically sourced automatic tangential creasing digital flatbed cutter.

Current Known Source:  TBD

Place of Performance: USDA, ARS, National Animal Disease Center, Visual Services in Ames, IA.

Anticipated Solicitation Release: July 31, 2026

Estimated Delivery: Delivery is expected within ninety days after award for the paddle blender.  

Description of Supply and Service

EQUIPMENT REQUIREMENTS must meet or exceed the following:

Flatbed capable of simultaneously creasing and cutting 2.5 kg of creasing force for thicker stock High-capacity auto feeder - 2,000 sheets 1,200 mm/sec cutting speed Portrait or landscape sheet feed Rear mark scanning system for accurate front-side cutting and back-side creasing Cut any contour or design without steel dies Two-zone vacuum bed for precise cutting across entire surface Adobe Illustrator plugins One-year warranty coverage for parts and labor One-year of software support

Disclaimers:

This notice is posted in accordance with FAR Part 5.2. In accordance with FAR Part 4.1102, Procedures, System for Award Management (SAM), potential contractors must be registered in SAM prior to submitting responses, proposals, bids, or quotes. Offerors may obtain information on registration at https://www.sam.gov. Any potential future solicitations will be posted exclusively on SAM.gov. Interested parties are responsible for monitoring this website for the release of solicitation and any updates or amendments. Do NOT submit proposals, bids, or quotes at this time. The Government does not intend to pay for any information provided under this notice.

Instructions For Interested Parties, Capabilities:

Companies who have experience, as well as an interest in doing business with ARS, should submit a Capabilities Statement which, for this notice, is not expected to be a proposal, but rather short statements regarding the company’s ability to demonstrate their expertise and experience in relation to the areas specified in this notice. Companies should also indicate whether they are a Small Business, SBA-certified HUBZone, SBA-certified 8(a), SDVOSB, or Women-Owned Small Business as well as the Country of Origin of the proposed instrument and accessories. Responses should be submitted by July 24, 2026, no later than 3:00 p.m. EDT to the attention of Shelley Steen at shelley.steen@usda.gov.

View original listing