SAM #N0010426QFD47

Solicitation for Refurbishment and Repair of Shipboard Cable Assembly (NAVSUP WSS MECH)

NAVSUP Weapon Systems Support Mechanicsburg (NAVSUP WSS MECH), part of the Department of the Navy, is seeking refurbishment and repair services for a Cable Assembly, Inboard used in shipboard systems. - Government Buyer: - Department of the Navy, NAVSUP Weapon Systems Support Mechanicsburg (NAVSUP WSS MECH) - OEMs and Vendors: - Huntington Alloys (testing/certification) - Metallurgical Consultants (testing/certification) - Naval Surface Warfare Center Carderock (testing/certification) - Teledyne Allvac (testing/certification) - Westmoreland Mechanical Testing (testing/certification) - Mannesmann Rohrenwerke (testing/certification) - ThyssenKrupp VDM USA (testing/certification) - Products/Services Requested: - Refurbishment and repair of Cable Assembly, Inboard per NAVSEA drawings/specifications (EB-4707, PSSSN21C-306, 5613017, 5613018, 5613022, 5615883, 5615884, 7491198, 7491200, 7491201, 7491202) - Key materials: QQ-N-286 (annealed and age hardened) for body, nut, header, washer - Teardown, evaluation, inspection, and repair to 'like new' or 'A' condition - Unique/Notable Requirements: - Strict material traceability and certification - No use of molybdenum disulfide thread lubricants - Compliance with ISO-9001, ISO-10012, ANSI-Z540.3, MIL-I-45208, MIL-STD-45662, FED-STD-H28, MIL-STD-792, MIL-STD-2035, MIL-STD-2132 - Testing/certification must be performed by approved laboratories (listed above) - Firm fixed price quotes required for both repair and beyond economic repair scenarios

Description

CONTACT INFORMATION 4 | N743.49 | WVE | 771-229-0573 | benjamin.t.spangler.civ@us.navy.mil ITEM UNIQUE IDENTIFICATION AND VALUATION (JAN 2023) 19 HIGHER-LEVEL CONTRACT QUALITY REQUIREMENT (DEC 2014) 1 | See specification sections C and E. INSPECTION OF SUPPLIES--FIXED-PRICE (AUG 1996) 2 INSPECTION AND ACCEPTANCE - SHORT VERSION 8 GENERAL INFORMATION-FOB-DESTINATION 1 | B WIDE AREA WORKFLOW PAYMENT INSTRUCTIONS (JAN 2023) 16 | Stand-Alone Receiving Report - Certifications Combo - Receiving Report & Invoice - Material | N/A | TBD | N00104 | TBD | N39040 - Certifications, S4306A - Material | N50286 | TBD | 133.2 | N/A | N/A | N39040 - Certifications | N/A | N/A | SEE DD FORM 1423 | PORT_PTNH_WAWF_NOTIFICATION@NAVY.MIL | BENJAMIN.T.SPANGLER.CIV@US.NAVY.MIL NAVY USE OF ABILITYONE SUPPORT CONTRACTOR - RELEASE OF OFFEROR INFORMATION (3-18) 1 MANDATORY USE OF WORKFLOW PRO (WFP) MOD ASSIST MODULE 1 WARRANTY OF SUPPLIES OF A NONCOMPLEX NATURE (JUNE 2003) 6 | One year from date of delivery. BUY AMERICAN-FREE TRADE AGREEMENTS-BALANCE OF PAYMENTS PROGRAM-BASIC (FEB 2024) 11 SMALL BUSINESS SUBCONTRACTING PLAN (DOD CONTRACTS)-BASIC (DEV 2026-O0037)(FEB 2026) 2 WARRANTY OF DATA-BASIC (DEVIATION 2026-O0035) (FEB 2026) 2 NOTICE OF TOTAL SMALL BUSINESS SET-ASIDE (DEV 2026-O0037)(FEB 2026) 1 SECURITY PROHIBITIONS AND EXCLUSIONS (CLASS DEVIATION 2026-O0025)(FEB 2026) 7 BUY AMERICAN-FREE TRADE AGREEMENTS-BALANCE OF PAYMENTS PROGRAM CERTIFICATE-BASIC (FEB 2024) 5 BUY AMERICAN-BALANCE OF PAYMENTS PROGRAM CERTIFICATE-BASIC (FEB 2024) 1 ALTERNATE A, ANNUAL REPRESENTATIONS AND CERTIFICATIONS (DEVIATION 2026-O0043)(FEB 2026) 13 NOTICE OF PRIORITY RATING FOR NATIONAL DEFENSE, EMERGENCY PERPARDENESS, AND ENERGY PROGRAM USE (APRIL 2008) 2 | X NOTES: 1. DD1423 Data Item A001 (Inspection and Test Plan) may be waived if already on file at NAVSUP WSS Mechanicsburg. 2. Portsmouth NSY's DODAAC has changed from N00102 to N50286. Any reference to N00102 within this order should be updated to N50286. 3. The following proposed delivery schedule applies: Submission of Certification Data CDRLs will be on or before 20 days prior to scheduled delivery. PNSY review/acceptance of Certification CDRLs 6 working days after receipt of Certification DD 1423 CDRLs. Final delivery of material will be on or before 110 days after effective date of the resulting contract. 4. Any contract awarded as a result of this solicitation will be "DO" rated order; "DO" rated order certified for national defense use under the Defense Priorities and Allocations System (DPAS). 5. NAVSUP WSS Mechanicsburg will be considering past performance in the evaluation of offers in accordance with DFARS 252.204-7024. 6. If drawings are included in the solicitation, access needs to be requested on the individual solicitation page on Contracts Opportunities on the Government's SAM.gov website. After requesting access, send an email to the Primary POC listed on the solicitation. 7. This is a Level 1 Repair. 8. Please submit: FIRM FIXED PRICE (FFP). This includes the teardown, evaluation, inspection and full repair of the item to "like new" or "A" condition. See statement of work in solicitation. Please also provide an approximate cost of new item if available. 9. A beyond repair (BR)/ beyond economic repair (BER) price shall also be provided in addition to the repair price at time of submission of quote. 10. Do NOT include the cost for shipping material as the government implemented shipping system or ATAC will be shipping/delivering material. 11. This contract utilizes Commercial Asset Visibility (CAV). See clause NAVSUPWSSFA25 for further details. 1. SCOPE 1.1 The material covered in this contract/purchase order will be used in a crucial shipboard system. The use of incorrect or defective material would create a high probability of failure resulting in serious personnel injury, loss of life, loss of vital shipboard systems, or loss of the ship itself. Therefore, the material has been designated as SPECIAL EMPHASIS material (Level I, Scope of Certification, or Quality Assured) and special control procedures are invoked to ensure receipt of correct material. 2. APPLICABLE DOCUMENTS 2.1 Order of Precedence - In the event of a conflict between the text of this contract/purchase order and the references and/or drawings cited herein, the text of this contract/purchase order must take precedence. Nothing in this contract/purchase order, however, must supersede applicable laws and regulations unless a specific exemption has been obtained. 2.2 Applicable Documents - The document(s) listed below form a part of this contract/purchase order including modifications or exclusions. 2.2.1 Specification Revisions - The specification revisions listed under "Documents References" below are the preferred revision. Older and/or newer revisions are acceptable when listed within Contract Support Library Reference Number CSD155 in ECDS (Electric Contractor Data Submission) at: https://register.nslc.navy.mil/. This is to allow Contractors to use certain acceptable older specification revisions to purge their existing stock of material certified to those older revisions or to use newer specification revisions when material is certified to newly released revisions, without requiring the submittal of waiver/deviation requests for each specification revision on every contract. Revisions of specifications reflecting editorial and/or re-approval (e.g., E2009, R2014, etc.) are considered inconsequential, but are acceptable when their revisions are listed within CSD155 or elsewhere within this contract. 2.2.2 Documents, drawings, and publications supplied are listed under "Drawing Number". These items should be retained until an award is made. 2.2.3 "Document References" listed below must be obtained by the Contractor. Ordering information is included as an attachment to this contract/purchase order. DRAWING DATA=EB-4707 | 96169 | A | SP | D | 0001 | A | 49998 | 0034417 DRAWING DATA=EB-4707 | 96169 | A | SP | D | 0002 | A | 49998 | 0010228 DRAWING DATA=EB-4707 | 96169 | A | SP | D | 0003 | A | 49998 | 0009688 DRAWING DATA=EB-4707 | 96169 | A | SP | D | 0004 | A | 49998 | 0015196 DRAWING DATA=EB-4707 | 96169 | A | SP | D | 0005 | A | 49998 | 0042460 DRAWING DATA=EB-4707 | 96169 | A | SP | D | 0006 | A | 49998 | 0013600 DRAWING DATA=EB-4707 | 96169 | A | SP | D | 0007 | A | 49998 | 0025918 DRAWING DATA=EB-4707 | 96169 | A | SP | D | 0008 | A | 49998 | 0027475 DRAWING DATA=EB-4707 | 96169 | A | SP | D | 0009 | A | 49998 | 0035849 DRAWING DATA=EB-4707 | 96169 | A | SP | D | 0010 | A | 49998 | 0026286 DRAWING DATA=EB-4707 | 96169 | A | SP | D | 0011 | A | 49998 | 0027109 DRAWING DATA=EB-4707 | 96169 | A | SP | D | 0012 | A | 49998 | 0040703 DRAWING DATA=EB-4707 | 96169 | A | SP | D | 0013 | A | 49998 | 0040998 DRAWING DATA=EB-4707 | 96169 | A | SP | D | 0014 | A | 49998 | 0043207 DRAWING DATA=EB-4707 | 96169 | A | SP | D | 0015 | A | 49998 | 0037818 DRAWING DATA=EB-4707 | 96169 | A | SP | D | 0016 | A | 49998 | 0020883 DRAWING DATA=PSSSN21C-306 | 43689 | .5 | SP | D | 0001 | .5 | 49998 | 9999999 DRAWING DATA=5613017 | 53711 | B | | D | 0001 | A | 49998 | 0019951 DRAWING DATA=5613018 | 53711 | C | | D | 0001 | A | 49998 | 0020757 DRAWING DATA=5613022 | 53711 | C | | D | 0001 | A | 49998 | 0024067 DRAWING DATA=5615883 | 53711 | A | | D | 0001 | A | 49998 | 0038074 DRAWING DATA=5615884 | 53711 | A | | D | 0001 | A | 49998 | 0184459 DRAWING DATA=7491198 | 53711 | B | | D | | | DRAWING DATA=7491200 | 53711 | - | | D | 0001 | - | 49998 | 0204664 DRAWING DATA=7491201 | 53711 | A | | D | | | DRAWING DATA=7491202 | 53711 | - | | D | 0001 | - | 49998 | 0016034 DOCUMENT REF DATA=FED-STD-H28 | | | B | 190424 | A | | | DOCUMENT REF DATA=FED-STD-H28 | 0020 | | B | 941221 | A | | 01 | DOCUMENT REF DATA=ANSI/ASQ Z1.4 | | | | 080101 | A | | | DOCUMENT REF DATA=QQ-N-286 | | | G | 001207 | A | | | DOCUMENT REF DATA=MIL-STD-792 | | | F | 230223 | A | | 01 | DOCUMENT REF DATA=MIL-STD-2035 | | | A | 950515 | A | | | DOCUMENT REF DATA=MIL-STD-2132 | | | D | 080310 | F | | 01 | DOCUMENT REF DATA=ISO_9001 | | | | 081115 | A | | | DOCUMENT REF DATA=ISO10012 | | | | 030415 | A | | | DOCUMENT REF DATA=ISO/IEC 17025 | | | | 050515 | A | | | DOCUMENT REF DATA=MIL-I-45208 | | | A | 810724 | A | 1 | | DOCUMENT REF DATA=MIL-STD-45662 | | | A | 880801 | A | | | DOCUMENT REF DATA=A-A-59004 | | | B | 081118 | A | | | DOCUMENT REF DATA=ANSI/NCSL Z540.3 | | | | 130326 | A | | | DOCUMENT REF DATA=0900-LP-001-7000 | | | | 810101 | C | | 01 | DOCUMENT REF DATA=S9074-AQ-GIB-010/248 | | | 1 | 191112 | A | | | DOCUMENT REF DATA=T9074-AS-GIB-010/271 | | | 1 | 140911 | A | | | DOCUMENT REF DATA=S9074-AR-GIB-010A/278 (CHG A) | | | | 130214 | A | | | 3. REQUIREMENTS 3.1 REFURBISHED MATERIAL STATEMENT OF WORK (REPAIR SOW) - 3.1.1 INSPECTION - Clean and determine if refurbishment is possible. At disassembly, the Contractor must record all identifying markings found on the parts of each assembly. The Contractor must maintain traceability of these markings to each unit throughout refurbishment. 3.1.2 IDENTIFYING MARKINGS - Part must have a MIC (Material Identification and Control) code, heat/heat lot code, or unique Contractor traceability number/code that is visible on the part. See Material Traceability in paragraph 3 (Quality Assurance Provisions) of this contract for traceability requirements. The MIC code can consist of a 2, 3, or 4 letter material identifier, 4 or 5 digit Julian date, 3 digit lot serial number, and Certifying Activity Designator (CAD) which will be 1 or 2 letters; the 4 parts are normally separated by hyphens; examples: TIA-3089-30-QQ and ST-06262-506-A. 3.1.3 RE-USEABLE PARTS - Any parts of the original assembly that are useable (replacement is not necessary), that are properly marked as identified above, and that have material certifications available may be utilized as initially supplied. Certifications are not required to be resubmitted by the contractor. Any parts of the original assembly that are useable (replacement is not necessary), are properly marked as identified above, but material certifications are not available at the contractor's facility, a waiver must be submitted in accordance with Waiver/Deviation (Configuration Control) requirements specified elsewhere in the Contract. 3.1.4 NON-USEABLE PARTS - Any parts of the original assembly that are not properly marked as identified above must be replaced and the required certifications must be submitted. Any parts of the original assembly that are not usable (replacement is necessary) must be replaced and the required certifications must be submitted. 3.1.5 REFURBISHMENT - Upon completion of inspection, this item must be refurbished to be in accordance with ;Naval Sea Systems Command Drawing 7491198 and Maintenance Standard 1110-081-022 Revision B (CSD695); , except as amplified or modified herein. This applies to all "Parts Requiring Certification" as identified elsewhere in this Contract/Purchase Order. 3.1.6 ADDITIONAL SOW REQUIREMENTS - ;N/A; 3.2 ;General Note 4 on NAVSEA Drawing 5615883 which states "Assemble according to LaBarge Document# 5615879w/ 5613012" and General Note 5 on NAVSEA Drawing 5615883 which states "Inspect and test according to LaBarge Document ITI #574" are not applicable.; 3.3 ;Penetrator wiring must be modified per EB Specification 4707. Hook up of the penetrator conductors to the penetrator header assembly must follow the color code convention of EB Specification 4707. Inboard ends of wires and shields extending from the penetrator header assembly must be marked with the pin number to which they are attached.; 3.4 Contract Support Library - Additional requirements for this item are identified as Contract Support Library Reference Number ;CSD695; in ECDS at https://register.nslc.navy.mil/ 3.5 Material for Parts Requiring Certification - Quantitative chemical and mechanical analysis is required for the parts listed below unless specifically stated otherwise: Part - ;Body, Part 306/1-001 on drawing PSSSN21C-306; Material - ;QQ-N-286, annealed and Age Hardened (Mechanical properties to be in accordance with PSSSN21C-306 PARA 3.3.2); Part - ;Nut, Part 306/1-006 on drawing PSSSN21C-306; Material - ;QQ-N-286, Annealed and Age Hardened (Mechanical Properties to be in accordance with PSSSN21C-306 PARA 3.3.2); Part - ;Header, Part 306/1-013 on drawing PSSSN21C-306; Material - ;QQ-N-286, Annealed and Age Hardened (Mechanical Properties to be in accordance with PSSSN21C-306 PARA 3.3.2); Part - ;Washer, Part 306/1-007 on drawing PSSSN21C-306; Material - ;QQ-N-286, Annealed and Age Hardened (Mechanical Properties in accordance with PSSSN21C-306 PARA 3.3.2); 3.6 Testing Certification - Certifications are required for the following tests on the items listed below. Additional testing on other piece parts (if any) per applicable drawings and specifications is still required, but certifications are only required as listed below. Test - Non-Destructive Tests Item - ;Weld Repair and/or Production Weld (as applicable); Performance - Per applicable fabrication specification Acceptance - Per applicable fabrication specification Test - ;Dye Penetrant Inspection; Item - ;Body, Nut, Header, and Washer; Performance - T9074-AS-GIB-010/271 Acceptance - MIL-STD-2035 Test - Ultrasonic Inspection on Starting Material Item - ;All Items requiring certification made from QQ-N-286 with a diameter or minimum distance between parallel surfaces of 4 inches or greater of the starting material, or when required by a drawing or specification invoked elsewhere in this contract; Performance - T9074-AS-GIB-010/271 or MIL-STD-2132, and QQ-N-286 Acceptance - QQ-N-286 Attribute - Annealing and Age Hardening Item - ;Body, Nut, Washer, and Header; Performance - QQ-N-286 Test - ;Post-Overhaul Test; Item - ;Each Penetrator Assembly; Performance - ;Paragraph 1.d of Maintenance Standard 1110-081-022 (CSD695); Acceptance - ;Paragraph 1.d of Maintenance Standard 1110-081-022 (CSD695); 3.7 Slow Strain Rate Tensile Test Laboratories - The Slow Strain Rate Tensile Test of QQ-N-286 must be performed by one of the following laboratories: Huntington Alloys, a Special Metals CompanyAttn: Bill Bolen3200 Riverside DriveHuntington, WV 257059Phone: (304) 526-5889FAX: (304) 526-5973 Metallurgical Consultants, Inc.Attn: W. M. Buehler4820 CarolinePO Box 88046Houston, TX 77288-0046Phone: (713) 526-6351FAX: (713) 526-2964 Naval Surface Warfare Center, Carderock DivisionAttn: Eric Focht Code 6149500 Macarthur BlvdWest Bethesda, MD 20817-5700Phone: (301) 227-5032FAX: (301) 227-5576 Teledyne AllvacAttn: Dr. W. D. Cao2020 Ashcraft Ave.Monroe, NC 28110Phone: (704) 289-4511FAX: (704) 289-4269 Westmoreland Mechanical Testing and Research Inc.Attn: Andrew WisniewskiP.O. Box 388Youngstown, PA 15696-0388 Mannesmann RohrenwerkeMannesmann Forschungsinstitut (MFI)Attn: Dr. WeissPostfach 25116047251 DuisburgGermanyPhone: 011-49-0203-9993194FAX: 011-49-0203-9994415 ThyssenKrupp VDM USA, Inc.Attn: D. C. Agarwal11210 Steeplecrest Drive, Suite 120Houston, TX 77065-4939Phone: (281) 955-6683 3.8 Thread Inspection Requirements All threads on threaded parts must be inspected using appropriate inspection methods, inspection systems, and inspection gauges/instruments in accordance with FED-STD-H28 series. Substitution of the commercial equivalent inspection in accordance with ASME B1 series is acceptable. 3.8.1 System 21 of FED-STD-H28/20 must be used as a minimum inspection requirement for threads when the design drawing or design specification does not specify an inspection requirement. 3.8.2 For Navy and Shipyard drawings, system 21 of FED-STD-H28/20 may be substituted for System 22 without further Navy approval when the design drawing invokes System 22 and does not cite governing specifications that specifically require system 22. System 22 of FED-STD-H28/20 must be used when the drawing references other governing specifications that specifically require System 22, such as certain thread types of MIL-DTL-1222. 3.8.3 A written request for concurrence must be submitted when utilizing alternative measuring equipment or measuring systems not applicable to the specified inspection system. 3.9 Thread Lubricant Thread lubricants containing molybdenum disulfide must not be used on this material. Bacteria in water, especially seawater, causes molybdenum disulfide to break down. The by-products of the breakdown form compounds which attack the fasteners. Anti-galling compound A-A-59004 must be used as a replacement when thread lubricant is required for assembly. 3.10 Internal Threads All internal threads must be formed by cutting. Cold forming of internal threads is not acceptable. 3.11 O-ring grooves and mating sealing surfaces must be inspected per the contractually invoked drawings or specifications. When the drawings or specifications do not provide specific defect criteria or state that no defects are allowed, the General Acceptance Criteria (GAC) standard must be used for inspecting O-ring grooves and mating sealing surfaces only. Repairs to sealing surfaces and O-ring grooves with unacceptable defects may be accomplished within the limits of the size and tolerances provided in the applicable drawing. Repairs that would exceed these limits require approval (including final dimensions). The data that is red lined (crossed out) is excluded from the GAC for this contract and is not to be used for acceptance or rejection criteria. The GAC document is identified as Contract Support Library Reference Number CSD008 at https://register.nslc.navy.mil/ 3.12 Pressure Tolerance The pressure tolerance must be as specified in the assembly drawing, detail drawing, design specification or elsewhere in this contract. Where pressure tolerances are not provided by drawings, specifications or elsewhere in this contract, the following must be used: For pressure tests below 100 PSIG, the pressure tolerance must be +1 PSIG / -0 PSIG. For pressure tests at or above 100 PSIG up to and including 2500 PSIG, the pressure tolerance must be +2% / -0 PSIG rounded off to the nearest multiple of the smallest graduation on an analog test pressure gauge, not to exceed 50 PSIG. For pressure tests above 2500 PSIG, the pressure tolerance must be +2% / -0 PSIG, rounded off to the nearest multiple of the smallest graduation on an analog test pressure gauge, not to exceed 200 PSIG. The pressure test time tolerance must be as specified in the assembly drawing, detail drawing, design specification or elsewhere in this contract. Where pressure test time tolerances are not provided by drawings, specifications or elsewhere in this contract, the following must be used: For a test duration up to and including 1 hour, the tolerance must be +5 minutes / - 0 minutes. For a test duration of more than 1 hour up to and including 24 hours, the tolerance must be +30 minutes / - 0 minutes. For a test duration of more than 24 hours, the tolerance must be +60 minutes / - 0 minutes. 3.13 Welding or Brazing When welding, brazing, and allied processes are required, as invoked by Section C paragraph 3 requirements, they must be in accordance with S9074-AR-GIB-010A/278, 0900-LP-001-7000 for brazing of piping and pressure vessel applications, or S9074-AQ-GIB-010/248 for brazing of other applications. For all production and repair welding and brazing, personnel and procedures must be qualified under S9074-AQ-GIB-010/248 or 0900-LP-001-7000, as applicable. Repair welding is not permitted on ;QQ-N-286 material; . Procedures and Qualification Data must be submitted for review and approval prior to performing any welding or brazing. 3.14 Certificate of Compliance (SPECIAL EMPHASIS MATERIAL) The Contractor must prepare and submit a certificate of compliance certifying that the items/components furnished under this contract comply with the requirements of the procurement document, including any/all invoked specifications and drawings. 3.15 Configuration Control The Contractor must maintain the total equipment baseline configuration. For items of proprietary design, Contractor drawings showing the latest assembly configuration must be provided to the Government in electronic (C4) format. Definitions are provided elsewhere in the Contract/Purchase Order. 3.15.1 Waivers/Deviations - All waivers and deviations, regardless of significance or classification require review and approval by the Contracting Officer. Waivers and Deviations must be designated as Critical, Major, or Minor. The Contractor must provide a copy of this request to the QAR. Requests must include the information listed below. A complete description of the contract requirement affected and the nature of the waiver/deviation (non-conformance), including a classification of Critical, Major, or Minor. Number of units (and serial/lot numbers) to be delivered in this configuration. Any impacts to logistics support elements (such as software, manuals, spares, tools, and similar) being utilized by Government personnel or impacts to the operational use of the product. Information about remedial action being taken to prevent reoccurrence of the non-conformance. 3.15.2 All requests for Waivers/Deviations on NAVSUP-WSS Contracts must be submitted to the NAVSUP WSS Contracting Specialist via eMail. 3.15.3 ECPs - The Government will maintain configuration control and change authority for all modifications or changes affecting form, fit, function, or interface parameters of the Equipment and its sub-assemblies. The Contractor must submit an Engineering Change Proposal (ECP) for any Class I or II changes that impact the Equipment covered by this contract. ECPs must be prepared in Contractor format, and must include the following information: The change priority, change classification (Class I or Class II), and change justification. A complete description of the change to be made and the need for that change. A complete listing of other Configuration Items impacted by the proposed change and a description of the impact on those CIs. Proposed changes to documents controlled by the Government. Proposed serial/lot number effectivities of units to be produced in, or retrofitted to, the proposed configuration. Recommendations about the way a retrofit should be accomplished. Impacts to any logistics support elements (such as software, manuals, spares, tools, and similar) being utilized by Government personnel in support of the product. Impacts to the operational use of the product. Complete estimated life-cycle cost impact of the proposed change. Milestones relating to the processing and implementation of the engineering change. 3.16 Mercury Free - Mercury and mercury containing compounds must not be intentionally added or come in direct contact with hardware or supplies furnished under this contract. Mercury contamination of the material will be cause for rejection. 3.17 NAVSEA 0948-LP-045-7010 - Any applicable requirements of NAVSHIPS 4410.17, NAVSEA 0948-LP-045-7010, or 0948-045-7010 which the contractor must meet are included in this contract/purchase order. The above documents are for Government Use Only. Further application of the above documents is prohibited. 3.17.1 Marking of material with a Material Designator per the Drawing is also prohibited, with the exception of Fasteners. Fasteners must be marked with a Material Symbol/Designator as specified elsewhere in this contract.

View original listing