SAM #W911S226U3076

Heavy Duty Gas Griddles and Installation for West Point

The Mission Installation Contracting Command (MICC) at Fort Drum, representing the Department of the Army, is seeking heavy duty gas griddles and installation services for West Point. - Government Buyer: - Mission Installation Contracting Command (MICC), Fort Drum - Department of the Army - Products and Accessories Requested: - Heavy duty gas griddles with stainless steel construction, 6 burners, 162,000 BTU, 2 drawers, 1-inch thick polished steel griddle plate, manual ignition, and natural gas compatibility - Gas flex hoses (1/2 inch x 4 ft, quick disconnect) – 4 units - Universal equipment stands (24 inch height, stainless steel, 5 inch casters) – 4 units - Griddle banking strips – 3 units - Services Required: - Delivery, unpacking, installation, and connection to existing supply lines - Assembly of water filter system - Removal of rubbish - Operational testing in presence of government point of contact - Unique Requirements: - Standard parts and warranty must be provided - Installation must include connection to existing power and water lines - OEMs and Vendors: - No specific OEMs or vendors are named in the solicitation - Place of Performance: - West Point military base, NY (zip 10996) - MICC Fort Drum contracting office, NY - SBA set-aside applies to this procurement.

Description

Heavy duty gas griddle, stainless steel front, sides and front top ledge. Fully welded stainless and aluminized steel body frame. 11 Inch low profile cooking height on 6 Inch legs.1 Inch thick polished steel griddle plate with 12-gauge, 4 Inch stainless steel back and tapered side splashes. 72 Inch W 31-1/2 Inch D 15-1/4 Inch H 6 Burners, 162,000BTU, 2 Drawers ? Fully welded stainless and aluminized steel chassis frame ? 11 Inch low profile cooking height on 4 Inch adjustable legs ? 1 Inch thick polished steel griddle plate with 12 gage, 10 Inch stainless steel back and tapered side splashes ? Spatula wide 3-1/2 Inch grease gutter and chute are fully welded for easier cleaning and to stop grease migration ? One 27,000 BTU/hr. U shaped aluminized steel burner for every 12 Inch of griddle width ? One embedded snap action thermostat per burner with temperature adjust from 200 Degree F to 550 Degree F on Steel or Chrome plate; temperature adjusts from200 Degree F to 450 Degree F on Rapid Recovery plate ? Large 6-quart stainless steel grease drawer (2 drawers on 60 Inch and 72 Inch models) ? Heavy duty chromed thermostat knob guards ? One pilot safety valve for every two burners; safety will completely shut off gas to pilot and burners if pilot extinguishes ? Manual ignition ? Bottom heat shields ? � Inch rear gas connection and gas pressure regulator supplied with the unit must be installed ? Natural Gas 4.0 Inch 3/4 rear gas connection. 4 each: HOSE � Inch x 4Ft long gas flex hose, and quick disconnect 4 each: Equipment Stand (STAND/C-72SA72)Universal equipment stand 24 Inch H, 1/2 Inch marine edge, undershelf, stainless steel, 5Inch casters 3 each: BANKING STRIP Griddle Banking Strips ? Deliver equipment with4eachall power and water lines for installation to existing supply lines. ? Unpack and install/connect/assemble new equipment and water filter system to existing supply lines and remove/discard all rubbish with installer. ? Once installed/connected, test equipment is fully operational in the presence of POC prior to departing the facility Standard Parts and Warranty Additional Links:Department of Defense Procurement ToolboxPIEE Solicitation Module Link for W911S226U3076Registration Instructions for the PIEE Solicitation ModuleWeb Based Training for the PIEE Solicitation Module

View original listing