SAM #W911S226U2899

The Mission Installation Contracting Command (MICC) at Fort Drum, on behalf of the Department of the Army, has updated its solicitation for fiber optic installation and maintenance supplies to be delivered or used at Fort Gordon, Georgia. - Government Buyer: - Department of the Army, Mission Installation Contracting Command (MICC), Fort Drum - OEMs and Vendors: - 3M (fiber connectors) - Electro-Wash (cleaning wipes) - FIS (cleaning solution) - Miller (Kevlar cutter scissors) - Products/Services Requested: - 3M 8300-W1K-S Single Mode SC Hot Melt Connector (Part# 8300) - 3M 8100YS ST Single Mode Hot Melt Fiber Connector (Part# 8100YS) - 3M SC Hot Melt Connector Multimode 125μm (Part# 6300W) - 3M ST Hot Melt Connector Multimode 125μm (Part# 6100) - Electro-Wash MX Cleaner Degreaser - Fiber Optic Strippers - FIS Cleaning Solution (99% alcohol) - Miller Kevlar Cutter Scissors - Unique or Notable Requirements: - Fiber connectors must use advanced adhesive technology for quick termination and fiber repositioning - All connectors must meet TIA/EIA 568-C.3 standards - Cleaning solution must be 99% alcohol for fiber optic use - Kevlar cutter scissors and fiber optic strippers are required for cable preparation - No specific quantities are provided for any items - Place of Performance/Delivery: - Fort Gordon, Georgia (primary delivery/use location) - MICC Fort Drum, New York (contracting office)

Reason for amendment 0001 was to update include additional items that was left off the solicitation. 8300-W1K-S Single Mode SC Hot Melt Connector with white 3mm boot Part# 8300. for 125�m fiber, 250/900�m jacketed cable features a zirconia ceramic ferrule with 0.2 dB typical loss for single mode fiber. It is specifically designed for ease of termination in local area networks. Pre-loaded with advanced re-heat able adhesive, this connector allows fiber repositioning and shows blue dot of adhesive after fiber insertion. It has no internal splice. No need for epoxy mixing. The termination time is about 2 minutes. The 8300-W1K-S hot melt connector meets TIA/EIA 568-C.3 standard for indoor and outdoor applications. WHITE boot. Sold 1 per package.002: 8100YS ST Single Mode Hot Melt Fiber Connector with Yellow 3MM Boot Part# 8100YS. For 125�m fiber features a zirconia ceramicferrulewith0.2 typical loss for single mode fiber. Specifically designed for quick, accurate and permanent field terminations in LAN intrabuilding environments. Color-coded yellow boot. Sold 1 per package.003: SC Hot Melt Connector Multimode 125�m 6300W These Hot Melt Fiber Optic Connectors utilize an advanced adhesive technology eliminating the application of epoxy. 3M Hot Melt Fiber Optic Connectors enable you to terminate fiberin2minutes or less. 3M Hot Melt Fiber Optic Connectors are re-heatable to allow for fiber repositioning. These fiber optic connectors have a typical loss of .2dB.0004: ST Hot Melt Connector Multimode 125�m 6100 These Hot Melt Fiber Optic Connectors utilize an advanced adhesive technology eliminating the application of epoxy. 3M Hot Melt Fiber Optic Connectors enable you to terminate fiber in 2 minutes or less. 3M Hot Melt Fiber Optic Connectors are re-heatable to allow for fiber repositioning. These fiber optic connectors have a typical loss of .2dB.0005: Electro-Wash MX Cleaner Degreaser is a high flash point cleaner that quickly removes soils, adhesives, and residues from insulation jackets and conductors on telecom, fiber optic and coaxial cables. Engineered with very low surface tension, this formulation penetrates and removes soils quickly with excellent wetting action, lifting and removing soils from the dirtiest areas. Electro-Wash MX Cleaner Degreaser is also ideal for removing carbonization, oxidized oils and greases from metal surface. Fiber Optic Strippers Precision Three Hole are large strip notch at the tip of the tool is used to remove1.6mm to 3.0mm jacketing. The middle strip notch is used to remove 600um to900um buffer. The smallest strip notch is used to strip the 250um coating to expose the 125umfiber cladding. The tool also has an easy-grip ergonomic handle and a closing latch to protect the stripping surface when not in use. FIS Cleaning solution 99% alcohol is 99% ACS reagent grade isopropyl is used in cleaning fiber connector end faces or prior to splicing. Miller Kevlar Cutter Scissor When cutting Kevlar, you need a cutting tool with very durable blades. You also want the tool to cut cleanly, and to fit comfortably in your hand. FIS offers Kevlar cutters that fit the bill. The Kevlar cutter, F1-KS1 (serrated), features vanadium steel serrated blades and high leverage cutting, utilizing long molded handles. Carbon Molybdenum and Vanadium Steel Blade. Ergonomic molded handles provide comfort in either hand. Additional Links:Department of Defense Procurement ToolboxPIEE Solicitation Module Link for W911S226U2899Registration Instructions for the PIEE Solicitation ModuleWeb Based Training for the PIEE Solicitation Module